AC Automatic Insulation/Withstanding HiTester 3174

(0) No Reviews yet
$5,775.00
SKU: 3174
Ships in approximately 115 days if not in stock.

Contact for Lead Time

Production delay is expected due to the worldwide component shortages. Please contact a Hioki representative for details.

The AC Automatic Insulation/Withstanding Tester 3174 is a low-cost solution featuring contact check functionality as well as a stabilized power supply to prevent the reduced test reliability that can result from these issues.

Key Features
- Continuous testing of insulation (500/1000 V) and withstand voltage (100 VA transformer capacity)
- Full remote operation when used in combination with the Safety Test Data Management Software 9267
- Save up to 8 test settings each for the withstanding and insulation testing modes
- Precise test voltage without power voltage dependency is generated using the PWM method

Product Warranty Period: 3 years

Included Accessories:
H.V. Test lead 9615 (high voltage side and return, 1 each) ×1, Power cord ×1, Instruction manual ×1, Disconnection prevention plate ×1
[Withstanding test section]
Testing voltage0.2 V AC to 5.00 kV AC
Voltage settingDigital setting, Setting resolution: 0.01 kV
Waveform/FrequencySine wave (Distortion ratio 5 % or less at no load), 50/60 Hz selectable
Current measurement0.01 mA to 20.0 mA, True RMS rectified (digital display)
Measurement range10 mA (0.01 mA resolution), 20 mA (0.1 mA resolution)
Voltage meterAccuracy: ±1.5 % rdg. (1000 V or more), ±15 V (less than 1000 V), True RMS rectified
Judgment functionWindow comparator method (Digital setting)
[Insulation test section]
Testing voltage500 V DC, 1000 V DC
Unloaded voltage1 to 1.2 times rated voltage
Rated testing current1 to 1.2 mA, Shorted current: 4 to 5 mA (at 500 V), 2 to 3 mA (at 1000 V)
Measurement range, Accuracy0.5 MΩ to 999 MΩ (at 500 V), and 1 MΩ to 999 MΩ (at 1000 V): ±4 % rdg.,
1000 MΩ to 2000 MΩ: ±8 % rdg.
Judgment functionWindow comparator method (Digital setting)
[Timer section]*Test times may differ from set timer times depending on the load.
Setting range0.3 to 999 s
Ramp, DelayTesting voltage ramp-up, or down, Insulation test delay: 0.1 to 99.9 s
[General section]
FunctionsSaving 8 testing conditions, hold, buzzer, contact check
Monitor functionOutput voltage, detected current, insulation resistance, Refresh rate: 2 times/s
Power supply100 to 240 V AC, (50/60 Hz), 200 VA max.
Dimensions and mass320 mm (12.60 in)W × 155 mm (6.10 in)H × 395 mm (15.55 in)D, 15 kg (529.1 oz)
Included AccessoriesH.V. Test lead 9615 (high voltage side and return, 1 each) ×1, Power cord ×1, Instruction manual ×1, Disconnection prevention plate ×1
ACCESSORIES


REMOTE CONTROL BOX (SINGLE) 9613
- For Start/Stop control, 1.5m (4.92 ft) cord length


REMOTE CONTROL BOX (DUAL) 9614
- For Start/Stop control, 1.5m (4.92 ft) cord length


H.V. TEST LEAD 9615
- Red, Black each 1, 1.5 m (4.92 ft) length, bundled


SAFETY TEST DATA MANAGEMENT SOFTWARE 9267
- PC software for use with HIOKI electrical safety testers
- Inspect, record and save measurement data according to electrical safety standards controlling electrical safety measuring instruments 
- Test insulation, withstand voltage (hipot), protective continuity, and leakage current


RS-232C CABLE 9637
- 9 pin - 9 pin, cross, 1.8 m (5.91 ft) length


GP-IB CONNECTOR CABLE 9151-02
- 2 m (6.56 ft) length

Ratings & Reviews

No reviews available

Be the first to Write a Review