Chemical Impedance Analyzer IM3590

(0) No Reviews yet
$10,225.00
SKU: IM3590
Ships in approximately 20 days if not in stock.

Contact for Lead Time

Production delay is expected due to the worldwide component shortages. Please contact a Hioki representative for details.

Hioki LCR Meters and Impedance Analyzers range from 1mHz to 3GHz devices to suit a wide range of applications in the testing of electronic components.. The IM3590 impedance analyzer is an advanced component tester especially suited to electrochemical impedance measurements and includes a variety of graphing functions that are needed for battery and chemical material testing.

Key Features
- Broad 1 mHz to 200 kHz signal source range supports measurements of ion behavior and solution resistance
- Continuous measuring and high-speed testing of LCR and sweep measurements with a single instrument
- Measure internal impedance of batteries with no load
- Perform high-speed sweep measurements in as little as 2 ms
- Basic accuracy of 0.05% is ideal for applications from component testing to R&D
- Measure LCR impedance for Cole-Cole plots and equivalent-circuit analyses of electro-chemical components and materials

Product Warranty Period: 3 years

Included Accessories:
Power cord ×1, Instruction manual ×1, CD-R (Communication instruction manual and sample software [Communications control, accuracy calculation, and screen capture functionality] ) ×1
Measurement modesLCR mode, Continuous measurement mode (LCR mode / Analyzer mode), Analyzer mode (Sweeps with measurement frequency and measurement level, temperature characteristics, equivalent circuit analysis)
Measurement parametersZ, Y, θ, Rs (ESR), Rp, Rdc (DC resistance), X, G, B, Cs, Cp, Ls, Lp,
D (tanδ), Q, T, σ (conductivity), ε (dielectric constant)
Measurement range100 mΩ to 100 MΩ, 10 ranges (All parameters are determined according to Z)
Display rangeZ, Y, Rs, Rp, Rdc, X, G, B, Ls, Lp, Cs, Cp, σ, ε :
±(0.00000 [unit] to 9.99999G [unit], Absolute value display for Z and Y only
θ : ±(0.000° to 180.000°), D : ±(0.00000 to 9.99999)
Q : ±(0.00 to 99999.9), Δ % : ±(0.0000% to 999.999%)
T : -10.0°C to 99.9°C
σ, ε :±(0.00000f [unit] to 999.999G [unit]
Basic accuracyZ: ±0.05% rdg. θ: ±0.03°
Measurement frequency1 mHz to 200 kHz (5 digits setting resolution, minimum resolution 1 mHz)
Measurement signal levelNormal mode:
V mode/CV mode: 5 mV to 5 Vrms, 1 mVrms steps
CC mode: 10 μA to 50 mArms, 10 μArms steps
Low impedance high accuracy mode:
V mode/CV mode: 5 mV to 2.5 Vrms, 1 mVrms steps
CC mode:10 μA to 100 mArms, 10 μArms steps
Output impedanceNormal mode: 100 Ω, Low impedance high accuracy mode: 25 Ω
Display5.7-inch color TFT, display can be set to ON/OFF
Measurement time2 ms (1 kHz, FAST, display OFF, representative value)
FunctionsDC bias measurement, DC resistance temperature compensation (converted reference temperature is displayed), Temperature measurement, Battery mesurement (Automatic DC biasing system), Comparator, BIN measurement (classification), Panel loading/saving, Memory function
InterfacesEXT I/O (Handler), USB communication (high-speed), USB memory
Optional: Choose 1 from RS-232C, GP-IB, or LAN
Power supply100 to 240 V AC, 50/60 Hz, 50 VA max.
Dimensions and mass330 mm (12.99 in) W × 119 mm (4.69 in) H × 168 mm (6.61 in) D, 3.1 kg (109.3 oz)
Included AccessoriesPower cord ×1, Instruction manual ×1, CD-R (Communication instruction manual and sample software [Communications control, accuracy calculation, and screen capture functionality] ) ×1
ACCESSORIES



SMD TEST FIXTURE IM9100
- Direct-connection testing
- Test SMDs with electrodes on the bottom
- DC to 8MHz
- Measurable sample sizes: 01005 to 0402 (EIA)



4-TERMINAL PROBE 9140-10
- Cable length 1 m (3.28 ft), DC to 200 kHz, impedance characteristics of 50 Ω, 4-terminal pair configuration, measurable conductor diameter: ø0.3 (0.01 in) to 5 mm (0.20 in)



TEST FIXTURE 9261-10
- Cable length 1 m (3.28 ft), DC to 8 MHz, impedance characteristics of 50 Ω, 4-terminal pair configuration, measurable conductor diameter: ø0.3 (0.01 in) to 1.5 mm (0.06 in)



TEST FIXTURE 9262
- Direct connection type, DC to 8 MHz, measurable conductor diameter: ø0.3 (0.01 in) to 2 mm (0.08 in)



SMD TEST FIXTURE 9263
- Direct connection type, DC to 8 MHz, Test sample dimensions:1 mm (0.04 in) to 10 mm (0.39 in)



DC BIAS VOLTAGE UNIT 9268-10
- Direct connection type, 40 Hz to 8 MHz, maximum applied voltage of DC ±40 V



DC BIAS CURRENT UNIT 9269-10
- Direct connection type, 40 Hz to 2 MHz, maximum applied current of DC 2 A



4-TERMINAL PROBE 9500-10
- Cable length 1 m (3.28 ft), DC to 200 kHz, impedance characteristics of 50 Ω, measurable conductor diameter: φ0.3 mm (0.01 in) to 2 mm (0.08 in)



SMD TEST FIXTURE 9677
- Direct connection type, For measuring SMDs with electrodes on the side; DC to 120 MHz, test sample dimensions: 3.5 mm ±0.5 mm (0.14 in ±0.02 in)



SMD TEST FIXTURE 9699
- Direct connection type, For measuring SMDs with electrodes on the bottom; DC to 120 MHz, test sample dimensions: 1.0 mm (0.04 in) to 4.0 mm (0.16 in) wide, max. 1.5 mm (0.06 in) high



CONTACT TIPS IM9901
- To replace the tip on the L2001, regular size, bundled with the L2001



CONTACT TIPS IM9902
- To replace the tip on the L2001, small size



4-TERMINAL PROBE L2000
- Cable length 1 m (3.28 ft), DC to 8 MHz, impedance characteristics of 50 Ω, 4-terminal pair configuration, measurable conductor diameter: ø0.3 (0.01 in) to 5 mm (0.20 in)



PINCHER PROBE L2001
- DC to 8MHz, 50Ω termination
- Tip electrode spacing: 0.3 to 6 mm
- Measurable sample size: 0603 (EIA)



SMD TEST FIXTURE IM9110
- For direct connection two-wire testing
- DC to 1 MHz
- Measurable sample size: 008004 (EIA)



GP-IB CONNECTOR CABLE 9151-02
- 2 m (6.56 ft) length



GP-IB INTERFACE Z3000
- GP-IB Interface



RS-232C INTERFACE Z3001
- RS-232C Interface



LAN INTERFACE Z3002
- Lan Interface



SWITCH MAINFRAME SW1001
- Pair with a measuring instrument for quick, multi-channel battery testing
- Max 60V DC input
- Max. 18 (4-terminal pair) to 66 (2-wire) channels



SWITCH MAINFRAME SW1002
- Pair with a measuring instrument for quick, multi-channel battery testing
- Max 60V DC input
- Max. 72 (4-terminal pair) to 264 (2-wire) channels

Ratings & Reviews

No reviews available

Be the first to Write a Review