Memory HiCorder MR8827

(0) No Reviews yet
$10,890.00
SKU: MR8827
Ships in approximately 20 days if not in stock.

Contact for Lead Time

Production delay is expected due to the worldwide component shortages. Please contact a Hioki representative for details.

Hioki Memory HiCorders are high-speed waveform monitoring and recording devices that can simultaneously measure multiple physical phenomena such as voltage, current, temperature, vibration, weight, acceleration and rotation due to complete isolation between channels and from each channel to the ground. More than just a digital oscilloscope, the MR8827 data acquisition (DAQ) recorder accommodates plug-and-play input modules to meet applications such as trial runs after the scheduled maintenance of railway cars to verify for voltage command signals, motor current, car speed, and brake pressure.

Key Features
- Generate and record waveforms with a single unit
- Output previously recorded problematic waveforms and apply to devices under test to simulate potential issues
- 32 analog + 32 logic channels to 28 analog + 64 logic channels
- High-speed sampling up to 20MS/s with fully isolated inputs
- Safe measurement with all isolated analog inputs
- Large capacity memory of total 512M-words
- Measure various system signals from high voltage to ultra low voltage simultaneously

Product Warranty Period: 3 years

Included Accessories:
Instruction manual ×1, Power cord ×1, Application disk (CD-R) ×1, Input cord label ×1, Printer paper ×1 (when ordering printer unit), Roll paper attachment ×2 (when ordering printer unit)
Max. Number of channels32 ch analog + 32 ch logic, or 28 ch analog + 64 ch logic (when use with built-in logic input + plug-in logic unit 8973 × 2)
Number of slots16 slots (Max. 16)
Number of logic channels32 ch logic (logic probe terminal GND share a common GND with chassis) Built-in logic input not available when using DVM Unit MR8990 on slots 1, 2, 9, or 10.

[Limitation on using built-in logic input] (with logic measurement ON)
• Measurement resolution on slots 1, 2, 9, and slot 10 is limited up to 12 bits
• Cannot use Frequency Unit 8970 on slots 1, 2, 9, or 10
Measurement ranges (20 div full-scale)[Analog Unit 8966]: 5 mV/div to 20 V/div, 12 ranges, resolution : 1/100 of range (using 12-bit A/D)
[High Resolution Unit 8968]: 5 mV/div to 20 V/div, 12 ranges, resolution : 1/1600 of range (using 16-bit A/D)
Max. allowable input400 V DC (using the 8966/8968)
Frequency characteristicsDC to 5 MHz (-3 dB, using the 8966), DC to 100 kHz (-3 dB, using the 8968)
Time axis (Memory function)5 µs to 5 min/div, 26 ranges, at 100 points/div resolution
Measurement functionsMemory (high-speed recording), Recorder (real-time recording), X-Y recorder, FFT
Other functionsNumerical calculation, Waveform processing, Waveform judgment (at Memory, or FFT function)
Memory capacity128M-words/ch (using 4 Analog channels) to 16M-words/ch (using 32 Analog channels), Total capacity 512MW memory
Data storage mediaUSB memory stick, CF card, Built-in SSD unit (option, 128GB) *Approx. 125 sec. when saving 100 MB of data
*Data of 100 MB in size can record 16,000 div waveforms across 32 channels.
Printing[Built-in A4-size printer option]: 216 mm (8.50 in) × 30 m (98.43 ft), thermal paper roll, Recording speed : Max. 50 mm (1.97 in)/s
Display10.4 inch TFT color LCD (SVGA, 800 × 600 dots)
External interfacesLAN: 100BASE-TX, USB 2.0 series A receptacle 2 port (for USB memory, mouse)
USB 2.0 series B receptacle (for communication with PC, mass storage)
Power supply100 to 240 V AC, 50/60 Hz (220 VA max., when using printer: 350 VA max.)
Dimensions and mass401 mm (15.79 in)W × 233 mm (9.17 in)H × 388 mm (15.28 in)D (including protruding parts except handle), 12.6 kg (444.4 oz) (main unit only)
Included AccessoriesInstruction manual ×1, Power cord ×1, Application disk (CD-R) ×1, Input cord label ×1, Printer paper ×1 (when ordering printer unit), Roll paper attachment ×2 (when ordering printer unit)
ACCESSORIES



CLAMP ON PROBE 3273-50
- DC to 50MHz (-3dB) 
- 30Arms maximum input 
- 0.1V/A output 
- φ 5 mm (0.20 in) core dia.



CLAMP ON PROBE 3276
- DC to 100MHz (-3dB) 
- 30Arms maximum input 
- 0.1V/A output 
- φ 5 mm (0.20 in) core dia.



CLAMP ON PROBE 3275
- DC to 2MHz (-3dB) 
- 500Arms maximum input 
- 0.01V/A output 
- φ 20 mm (0.79 in) core dia.



CLAMP ON PROBE 3274
- DC to 10MHz (-3dB) 
- 150Arms maximum input 
- 0.01V/A output 
- φ 20 mm (0.79 in) core dia.



CLAMP ON PROBE 9132-50
- Use for level measurement 
- 40 Hz to 1 kHz 
- 20 to 1000A AC 
- 0.2 V AC/range output 
- φ 55 mm (2.17 in) core dia.



CLAMP ON PROBE 9018-50
- Excellent phase characteristics 
- 40 Hz to 3 kHz 
- 10 to 500A AC 
- 0.2V AC/range output 
- φ 46 mm (1.81 in) core dia.



CONNECTION CORD L9217
- Cord has insulated BNC connectors at both ends, 1.6 m (5.25 ft) length



SSD UNIT U8330
- Specified upon order, built-in type, 128 GB



AC ADAPTER Z1008
- 100 to 240V AC



DIFFERENTIAL PROBE P9000
- Waveform only for exclusive use with Memory HiCorders (P9000-01) or waveform/RMS value switchable (P9000-02
- For use with input of up to 1 kV AC/DC 
- Requires separate power supply



CONNECTION CORD L9790
- Flexible φ 4.1 mm (0.16 in) thin dia. 
- Cable allowing for up to 600 V input 
- 1.8 m (5.91 ft) length



CONTACT PIN 9790-03
- Red/black set attaches to the ends of the Connection Cord L9790



ALLIGATOR CLIP L9790-01
- Red/black set attaches to the ends of the Connection Cord L9790



GRABBER CLIP 9790-02
- Red/black set attaches to the ends of the Connection Cord L9790



CONNECTION CORD L9197
- φ 5.0 mm (0.20 in) dia 
- Cable allows for up to 600 V input 
- 1.8 m (5.91 ft) length 
- Includes detachable large alligator clips



CONNECTION CORD L9198
- φ 5.0 mm (0.20 in) dia. 
- Cable allows for up to 300 V input 
- 1.7 m (5.58 ft) length 
- Small alligator clip



DIFFERENTIAL PROBE 9322
- For up to 2 kV DC or 1 kV AC 
- Use with AC Adapter 9418-15 
- Frequency band width up to 10MHz



AC ADAPTER 9418-15
- 100 to 240V AC



MAGNETIC ADAPTER SET L4937
- Attaches to the tip of the banana plug cable, CAT III 1000V



BUS BAR CLIP SET L4936
- Attaches to the tip of the banana plug cable, CAT III 600V



ALLIGATOR CLIP SET L4935
- Attaches to the tip of the banana plug cable, CAT IV 600V, CAT III 1000V



EXTENSION CABLE SET L4931
- Expands the length of the cable with banana plug, 1.5 m (4.92 ft) length



CONNECTION CABLE SET L4940
- Banana plug - banana plug, 1.5 m (4.92 ft) length, red/black each 1



TEST LEAD L2200
- 70 cm (2.30ft) length, detachable large alligator clips or needle tips are bundled, CAT IV 600V, CAT III 1000V



100:1 PROBE, 10:1 PROBE 9666, 9665
- Max. rated voltage to earth is same as for input module 
- 1.5 m (4.92 ft) length 
- Max. input voltage: 9666: 5 kV peak (up to 1MHz); 9665: 1 kV rms (up to 500 kHz)



LAN CABLE 9642
- Straight Ethernet cable, supplied with straight to cross conversion adapter, 5 m (16.41 ft) length



AC ADAPTER 9445-02
- For USA, 100 to 240 V AC, 9 V/ 1 A



CONVERSION CABLE 9323
- Used for connecting the 9320/9321/MR9321 and the 9324 to the Memory HiCorder with small logic terminal models



LOGIC PROBE MR9321,MR9321-01
- 4 isolated channels 
- ON/OFF detection of AC/DC voltage 
- Large terminal type



LOGIC PROBE 9320-01,9320
- 4 channels for contact voltage signals 
- 500ns response 
- Miniature terminal type



LOGIC PROBE 9327
- 4 channels for contact voltage signals 
- High-speed 100ns response



POWER SUPPLY 3269
- For Hioki wide bandwidth current probes 
- Connect up to four sensors



GRABBER CLIP 9243
- Attaches to the tip of the banana plug cable, Red/ Black: 1 each, 196 mm (7.72 in) length, CAT III 1000 V



CONVERSION ADAPTER 9199
- Receiving side banana, output BNC terminal



CONVERSION CABLE 9318
- To connect the CT6841-6846, CT6865/63/62, 9709, 9272-10 to the 8971/40/51, 38 cm (14.96 in) length



CONNECTION CORD 9165
- Cord has metallic BNC connectors at both ends, use at metallic terminal, 1.5 m (4.92 ft) length



CONNECTION CORD L9217
- Cord has insulated BNC connectors at both ends, 1.6 m (5.25 ft) length



CONNECTION CABLE L9795-01
- SMB to alligator clip, 1.5 m (4.92 ft) length



WAVEFORM GENERATOR UNIT MR8790
- 4 ch 
- DC output ± 10 V 
- Sinewave output 10 mHz to 20 kHz



PULSE GENERATOR UNIT MR8791
- 8 ch 
- Pulse output 0.1 Hz to 20 kHz 
- Pattern output



ARBITRARY WAVEFORM GENERATOR UNIT U8793
- 2ch, 10 mHz to 100kHz function generator 
- Arbitrary waveform generator function 2 MHz D/A refresh rate 
- Max.15 V output



LAN COMMUNICATOR 9333
- For LAN communication with the MR8740/8741, MR8847 series, 8826 
- For data collection and remote control



WAVE PROCESSOR 9335
- Convert data, print and display waveforms



FREQ UNIT 8970
- 2 ch, for measurement of frequency, rpm, pulse, etc.



HIGH VOLTAGE UNIT U8974
- 2 ch, 1000 V DC, 700 V AC max. voltage input



DIGITAL VOLTMETER UNIT MR8990
- 2 ch, high-precision DC V, 0.1 μV resolution, high-speed sampling 500 times/s



LOGIC UNIT 8973
- 4 terminals, 16 ch



DC/RMS UNIT 8972
- 2 ch, voltage/DC to 400 kHz, RMS rectifier, DC and 30 to 100 kHz bandwidth



CURRENT UNIT 8971
- 2 ch, for measuring current using dedicated current sensors, bundled two Conversion cable 9318



HIGH RESOLUTION UNIT 8968
- 2 ch, voltage input, DC to 100 kHz bandwidth



TEMP UNIT 8967
- 2 ch, thermocouple temperature input



ANALOG UNIT 8966
- 2 ch, Voltage input, DC to 5 MHz bandwidth



POWER SUPPLY 3272
- For Hioki wide bandwidth current probes 
- Single sensor connectable



AC ADAPTER Z1008
- 100 to 240V AC



PRINTER UNIT U8350
- Specified upon order. Printing width 200 mm (7.87 inch). Compatible recording paper: Model 9231



RECORDING PAPER 9231
- A4 width 216 mm (8.50 in) × 30 m (98.43 ft), 6 rolls/set

PC CARD 9830
- 2 GB capacity 
- PC card adapter bundled



PC CARD 1G 9729
- 1 GB capacity 
- PC card adapter bundled



PC CARD 512M 9728
- 512 MB capacity 
- PC card adapter bundled



EXTENSION CABLE SET L4931
- Expands the length of the cable with banana plug, 1.5 m (4.92 ft) length



GRABBER CLIP 9243
- Attaches to the tip of the banana plug cable, Red/ Black: 1 each, 196 mm (7.72 in) length, CAT III 1000 V
DOWNLOADS

Catalog
MEMORY HiCORDER MR8827

Declaration of Conformity
MEMORY HiCORDER MR8827

Ratings & Reviews

No reviews available

Be the first to Write a Review